Entrapment Protection Devices


Monitored entrapment protection devices are required to protect all entrapment zones in automated gate applications. Photo‐cells are used as type B1 (non‐contact sensors) devices. Electric edges are used as type B2 (contact sensors) devices.


Entrapment Protection Devices

 

Monitored Entrapment Protection

Type B1 non-contact devices (such as photo-beams) and/or Type B2 contact sensors (such as reversing edges) are required for most automatic gate system applications. DKS gate operators require a minimum of one (1) device to be connected in each direction of travel – otherwise, the operator will not run. All entrapment devices used with DKS gate operators are monitored per the requirements of the UL 325 Standard for Safety.

Non-Contact Photo Beam Detector
  • Compatible with all DKS Gate Operators.
  • When the Photo Beam is blocked by a person or object obstructing the gate path the Operator automatically reverses the gate to avoid injury and/or damage to the obstruction, gate, and Gate Operator.
  • Compliant with the UL 325 Standard for Safety.
  • Customers can add a Photo Beam to each end of the gate or pair it with the Edge Detector. When installed correctly and combined with the inherent Fail-Safe Clutch design this setup provides a safe operating environment.

Barrier Gate Safety

In today’s busy world people often forget to pay attention to their surroundings and can inadvertently place themselves in harm’s way. DKS Barrier Operators (1601, 1602, and 1603) now offer the DKS Pedestrian Protection System, a vehicular/pedestrian detection system that knows when it’s safe to allow the Barrier Arm to come down — or not. The System reverses the Barrier Arm if a person is detected, and lowers the Barrier Arm if an unauthorized vehicle enters, preventing accidents and injury.

 


Features

 

TYPE B1

Intended to be positioned in such a way that an obstruction in a hazardous area will interrupt the light beam. An interruption of the beam will signal the Operator to either stop, or stop and reverse motion. Complies with monitored external entrapment protection as per UL 325.

 

Reflective Photo Eyes

Reflective Photo Optic Systems consists of an Emitter/Receiver unit and a Reflector. Since the Reflector directs the beam back to the Photo Eye, wiring to the other side of the roadway is not required. These are typically used with shorter gates.

 

 

Thru-Beam Photo Eyes

Thru-Beam Photo Eye Systems consist of one Infrared Emitter and one Infrared Receiver housed and powered in separate units. These are typically used with longer gates.

 

It’s aware — even when they’re not.

In today’s busy world, people often forget to pay attention to their surroundings and can inadvertently place themselves in harm’s way. DKS Barrier Gate Operators offer a Pedestrian Detection & Protection System that knows when it’s safe to allow the Barrier Arm to come down — or not. Protect the integrity of the parking facility and prevent those inadvertent accidents from happening. After all, you have better things to do than deal with liability problems.

Reverse Edge 
  • A variety of edge styles.
  • Mounting channels included.
  • 2-wire edges can be hardwired.
IRB-MON
  • Infrared LED beam range 115 ft (35m).
  • Includes Emitter and Receiver.
  • Mounting bracket, other options available separately.
  • Operates over a wide range of 6-35 VDC and 12-24 VAC.
Enforcer
  • Mounting bracket and Reflector housing included.
  • Adjustable range up to 45 ft (14m).
  • 12-30V DC/AC 60H, 100mA.
IRB-RET
  • Pulsed near infrared light beam range 60 ft (18.3m).
  • Available with or without Reflector.
  • Includes mounting bracket with hardware.
  • Operates over a wide range of 6-35 VDC and 12-24 VAC
RG Reflecti-GUARD
  • Infrared beam range 7-30 ft (2.1-9.1 m).
  • Mounting hardware included.
  • Available as Relay Output or Pulsed Output.
  • Power: 7-30 VAC (50/60 Hz) or 10-42 VDC, 75mA
Photo-reflective Entrapment Protection Device
  • Receiver 18-32 VAC / VDC.
  • 35 ft (10.6 m) maximum sensing distance.
Adjustable Photo-reflective Entrapment Protection Device
  • Works with all DoorKing Gate Operators to comply with the UL 325 standards.
  • Receiver 18-32 VAC / VDC.
  • Deluxe housing simplifies installation.
  • 35 ft (10.6 m) maximum sensing distance

Technical Specifications

 

TYPE B1 NON-CONTACT SENSORS

Photo-Reflective Devices

8080-057 DKS Standard

  • 12-24 VAC / VDC
  • 35 Ft. (10.6m) maximum sensing distance

8080-060 DKS Deluxe

  • 12-24 VAC / VDC
  • 35 Ft. (10.6m) maximum sensing distance
  • Deluxe housing for simplified installation

8080-053 EMX IRB-RET

  • 12-24 VAC / 6-35 VDC
  • 60 Ft. (18m) maximum sensing distance

8080-055 Seco-Larm E936-S45RRGQ

  • 12-30 VAC / 12-30 VDC
  • 45 Ft. (14m) maximum sensing distance

8080-056 Omron E3K

  • 24-240 VAC / 24-240 VDC
  • 33 Ft. (10m) maximum sensing distance

 

Thru-Beam Devices

8080-050 ME-PG

  • Receiver: 7-30 VAC/10-42 VDC
  • Emitter: 1.5 VDC (battery powered, 2 AA Lithium)
  • 50 Ft. (15m) maximum sensing distance

8080-052 EMX IRB-MON

  • 12-24 VAC/6-35 VDC
  • 115 Ft. (35m) maximum sensing distance
  • Includes hood

8080-054 Thru-Beam (Seco-Larm E960-D90GQ)

  • 12-30 VAC/VDC
  • 90 Ft. (27m) maximum sensing distance

 

TYPE B2 CONTACT SENSORS

2-Wire Contac Edges with 10K Termination

8080-071 6-Foot Edge (ME111-T2)

  • Includes mounting channel – ideal for barrier arms

8080-070 5-Foot Edge (ME123-T2)

  • Includes mounting channel

8080-065 5-Foot Edge (MGR20-T2)

  • Designed to fit on 2-inch round gate post

8080-066 5-Foot Edge (MGS20-T2)

  • Designed to fit on 2-inch square gate post

4-Wire Contact Edges NO 10K Termination

8080-091 6-Foot Edge (ME111)

  • Includes mounting channel – ideal for barrier arms

8080-090 5-Foot Edge (ME123)

  • Includes mounting channel

8080-085 5-Foot Edge (MGR20)

  • Designed to fit on 2-inch round gate post

8080-086 5-Foot Edge (MGS20)

  • Designed to fit on 2-inch square gate post

Contact Sensor Accessories

8080-008 RF Monitored Gate Link Kit (RB-G-K10)

  • Receiver: 12-24 VAC/VDC
  • Transmitter RB-TX-10: 1.5 VDC (battery powered, 2 AA Lithium)
  • Receiver can monitor up to six contact edges

8080-006 Monitored Transmitter RB-TX-10

8080-079 Multi-Input Module (MIM-62)

  • 12-24 VAC/VDC
  • Monitors up to six external entrapment protection devices

  

 

  


Tech Support

Quick Start Guides icons accessory

Quick Start Guides

Owners Manuals icons accessory

Owner’s Manuals

Accessory Manuals icon accessory

Accessory Manuals

Easy Connect Manuals icon accessory

Easy Connect Manuals

Tech Tip Videos icons accessory

Tech Tip Videos


Resources

Photo-eye Reflective 8080-057
Photo-eye Reflective Deluxe 8080-060
Reverse Edge 8080 Series
Scroll to Top
Skip to content